<?xml version="1.0" encoding="UTF-8"?>
<rss version="2.0" xmlns:dc="http://purl.org/dc/elements/1.1/">
<channel>
<title>Forever CEL</title>
<description> 99 Boxster Base...After new Bank 2 solenoid/MAF/AOS/Battery/Plugs/Actuator Ramps both banks,I&#039;m right where I started CEL P1539 and some misfire codes here and there...Brought  to indie....said bent valves/actuator or timing....bailed on me....car is now at another indie. Any thoughts....car actually runs and sounds well with a little lacking in pickup. Any thoughts??</description><link>https://pedrosboard.com/read.php?7,51197,51197#msg-51197</link><lastBuildDate>Mon, 11 May 2026 08:24:03 -0400</lastBuildDate>
<generator>Phorum 5.2.23</generator>
<item>
<guid>https://pedrosboard.com/read.php?7,51197,57296#msg-57296</guid>
<title>Re: Forever CEL</title><link>https://pedrosboard.com/read.php?7,51197,57296#msg-57296</link><description><![CDATA[ Hey there,<br />How did you figure out it was the transistor? And whcih one was it? Can you please provide some deatails?<br />Thanks a million.]]></description>
<dc:creator>Du</dc:creator>
<category>Main Forum</category><pubDate>Wed, 08 Oct 2025 05:12:30 -0400</pubDate></item>
<item>
<guid>https://pedrosboard.com/read.php?7,51197,51228#msg-51228</guid>
<title>Re: Forever CEL</title><link>https://pedrosboard.com/read.php?7,51197,51228#msg-51228</link><description><![CDATA[ Just an update ...found a fried transistor in the DME, going to replace it and see if thats the problem.]]></description>
<dc:creator>vza</dc:creator>
<category>Main Forum</category><pubDate>Sun, 10 Mar 2019 18:01:48 -0400</pubDate></item>
<item>
<guid>https://pedrosboard.com/read.php?7,51197,51227#msg-51227</guid>
<title>Also...</title><link>https://pedrosboard.com/read.php?7,51197,51227#msg-51227</link><description><![CDATA[ I'm assuming you have no other codes. This type of code is meaningless unless other related codes have first been resolved.]]></description>
<dc:creator>Boxsterra</dc:creator>
<category>Main Forum</category><pubDate>Sun, 10 Mar 2019 15:23:28 -0400</pubDate></item>
<item>
<guid>https://pedrosboard.com/read.php?7,51197,51226#msg-51226</guid>
<title>I thought you replaced the actuators</title><link>https://pedrosboard.com/read.php?7,51197,51226#msg-51226</link><description><![CDATA[ If that's the case there's a low likelihood the problem is the actuator. Checking 12v is simply putting a volt meter on the 12v pin and ground and measuring the voltage. But there could be an intermittent ground or discontinuity. With the volt meter connected, wiggle all of the wires, check the electrical plugs to make sure they're all snug. If the 12v signal is unwavering, you will need to drive the car with a device that can monitor the 12v signal.]]></description>
<dc:creator>Boxsterra</dc:creator>
<category>Main Forum</category><pubDate>Sun, 10 Mar 2019 15:21:29 -0400</pubDate></item>
<item>
<guid>https://pedrosboard.com/read.php?7,51197,51218#msg-51218</guid>
<title>Re: Sounds like a wiring problem</title><link>https://pedrosboard.com/read.php?7,51197,51218#msg-51218</link><description><![CDATA[ ok...so if the actuator's getting power as the indie said it's definitely the actuator correct? What's the procedure for checking for 12v and triggering wire?]]></description>
<dc:creator>vza</dc:creator>
<category>Main Forum</category><pubDate>Fri, 08 Mar 2019 09:48:51 -0500</pubDate></item>
<item>
<guid>https://pedrosboard.com/read.php?7,51197,51204#msg-51204</guid>
<title>Re: Sounds like a wiring problem</title><link>https://pedrosboard.com/read.php?7,51197,51204#msg-51204</link><description><![CDATA[ He said actuator was getting power but would not activate or move when triggered w PIWIS I'm assuming its the actuator. V]]></description>
<dc:creator>vza</dc:creator>
<category>Main Forum</category><pubDate>Wed, 06 Mar 2019 22:27:10 -0500</pubDate></item>
<item>
<guid>https://pedrosboard.com/read.php?7,51197,51201#msg-51201</guid>
<title>Sounds like a wiring problem</title><link>https://pedrosboard.com/read.php?7,51197,51201#msg-51201</link><description><![CDATA[ <b>P1539 Camshaft Adjustment, Bank 2</b><br /><br /><i>1. Check B+ supply of actuator<br />2. Check triggering wire for continuity<br />3. Replace actuator</i><br /><br />Hopefully the tech went through steps 1 &amp; 2 before doing 3.]]></description>
<dc:creator>Boxsterra</dc:creator>
<category>Main Forum</category><pubDate>Wed, 06 Mar 2019 19:23:29 -0500</pubDate></item>
<item>
<guid>https://pedrosboard.com/read.php?7,51197,51197#msg-51197</guid>
<title>Forever CEL</title><link>https://pedrosboard.com/read.php?7,51197,51197#msg-51197</link><description><![CDATA[ 99 Boxster Base...After new Bank 2 solenoid/MAF/AOS/Battery/Plugs/Actuator Ramps both banks,I'm right where I started CEL P1539 and some misfire codes here and there...Brought  to indie....said bent valves/actuator or timing....bailed on me....car is now at another indie. Any thoughts....car actually runs and sounds well with a little lacking in pickup. Any thoughts??]]></description>
<dc:creator>vza</dc:creator>
<category>Main Forum</category><pubDate>Tue, 05 Mar 2019 18:28:13 -0500</pubDate></item>
</channel>
</rss>