Modes of Failure tonyd - Tuesday, 6 May, 2014, at 5:23:14 pm |
Interesting first post.... Roger987 - Tuesday, 6 May, 2014, at 6:41:41 pm |
Re: Interesting first post.... tonyd - Tuesday, 6 May, 2014, at 8:59:09 pm |
Modes of success... jlegelis - Tuesday, 6 May, 2014, at 8:30:41 pm |
Top down, October 2013 evening in New Hampshire Roger987 - Tuesday, 6 May, 2014, at 8:45:46 pm |
Re: Modes of failure... tonyd - Tuesday, 6 May, 2014, at 10:18:13 pm |
Lifter replacement is not an engine out job. The dealership doesn't bother cleaning them.. MarcW - Thursday, 8 May, 2014, at 12:20:06 pm |
Quote
tonyd
To give an optimistic example of Fixes, the Lifter issue is interesting.
Apparently the lifters can be dismantled,clean the ball, check the spring, inspect for cracks ,refill with oil and refit. The problem is I think this is an 'engine-out' job . So even if you have no lifter noise ,cleaning and inspecting them should(?) be on the to-do list when you have the engine out and apart. It would be a pity to miss this and then get lifter noise after you've re-installed the engine.
I wish the Variocam units were as easy/inexpensive to service as a dirty lifter..
Re: Lifter replacement is not an engine out job. The dealership doesn't bother cleaning them.. tonyd - Thursday, 8 May, 2014, at 12:24:48 pm |
An inspection may not spot a weak spring or a bad ball check valve seat that is allowing... MarcW - Friday, 9 May, 2014, at 11:01:04 am |
Quote
tonyd
Yes, but I have to remove the engine for other reasons anyway! And I have to emove the trans. And I hope not to repeat too often :-).
Thanks for confirming the importance of the issue. A careful cleaning and inspection will confirm is replacements are required.
If the concern is ticking noises, I previously linked to a piece that mentions several alternative and unrelated causes of the noise.That may be why some report lifter replacement was ineffective.
Many failures can be addressed by... grant - Tuesday, 6 May, 2014, at 8:47:24 pm |
Re: Modes of Failure tonyd - Tuesday, 6 May, 2014, at 9:57:12 pm |
Good objective, but i would suggest that you distinguish between grant - Wednesday, 7 May, 2014, at 11:03:05 am |
Re: Good objective, but i would suggest that you distinguish between tonyd - Wednesday, 7 May, 2014, at 11:49:51 am |
I dont have time to go into a lot of detail, but a quick read suggests grant - Thursday, 8 May, 2014, at 9:44:29 am |
For the little time invested, excellent summation, Grant *NM* Gary in SoFL - Thursday, 8 May, 2014, at 4:30:59 pm |
Re: I dont have time to go into a lot of detail, but a quick read suggests tonyd - Thursday, 8 May, 2014, at 4:55:45 pm |
I strongly disagree with the T-stat stuff. And science is on my side. grant - Thursday, 8 May, 2014, at 5:08:50 pm |
Re: I strongly disagree with the T-stat stuff. And science is on my side. tonyd - Thursday, 8 May, 2014, at 5:14:21 pm |
I didnt read it. I gave my assessment - its very simple. grant - Thursday, 8 May, 2014, at 6:56:24 pm |
OK, so i read. They argue that: grant - Thursday, 8 May, 2014, at 7:28:31 pm |
Re: Modes of Failure tonyd - Wednesday, 7 May, 2014, at 12:03:45 pm |
There is a fault... JM-Stamford,CT - Thursday, 8 May, 2014, at 10:32:50 am |
Re: There is a fault... tonyd - Thursday, 8 May, 2014, at 11:57:12 am |
Re: There is a fault... tonyd - Thursday, 8 May, 2014, at 12:14:19 pm |
Re: There is a fault... SORRY JM-Stamford,CT - Friday, 9 May, 2014, at 11:45:37 am |
You might as well list every rotating, reciprocating component as a failure. Given a large... MarcW - Thursday, 8 May, 2014, at 12:40:30 pm |
Here's my list of the 14 Modes of Failure Pedro (Odessa, FL) - Thursday, 8 May, 2014, at 5:44:49 pm |
Re: Here's my list of the 14 Modes of Failure tonyd - Thursday, 8 May, 2014, at 5:59:10 pm |
Maybe ... Pedro (Odessa, FL) - Thursday, 8 May, 2014, at 6:16:16 pm |
Re: Maybe ... Guenter in Ontario - Thursday, 8 May, 2014, at 7:31:23 pm |
Now there's a list i agree with, nearly 100%. And... grant - Thursday, 8 May, 2014, at 6:58:18 pm |
Re: Modes of Failure tonyd - Thursday, 8 May, 2014, at 6:05:22 pm |
Why is Hartech your Porsche Bible? Pedro (Odessa, FL) - Thursday, 8 May, 2014, at 6:20:52 pm |
Re: Why is Hartech your Porsche Bible? tonyd - Thursday, 8 May, 2014, at 9:09:09 pm |
How about "Notlob?" Laz - Friday, 9 May, 2014, at 7:41:28 am |
Look, if your real question is "what do i do to my motor now that its out" grant - Friday, 9 May, 2014, at 7:56:47 am |
Re: Why is Hartech your Porsche Bible? tonyd - 9 years ago |
Wow. 22/24 after one highway sweeper...????!!! grant - 9 years ago |
Hartech is the company that claims "thousands" of cars are at risk from a multitude of... MarcW - Friday, 9 May, 2014, at 11:22:38 am |
I am soooo bored of being scored *NM* grant - Friday, 9 May, 2014, at 5:06:46 pm |
Have you owned up to being honed up? *NM* Laz - Saturday, 10 May, 2014, at 2:10:04 pm |